Often asked: How To Finish Plywood Stairs?

Can you refinish plywood stairs?

Stairs can get worn out over time through constant use and traffic. If your stairs are in need of some refinishing and you don’t want to use carpet or tile, try paint! If your stairs are made of plywood, paint can give them a new life and completely change the look of your house.

Can you use plywood for stair treads?

While ¾” thick plywood or OSB is considered sufficiently thick for subfloors, it is not uncommon to use a thicker material for the stair treads. One inch of total plywood thickness is ideal and can be made from two layers of ½” plywood, bonded together.

How do you finish OSB stairs?

Painting OSB Stair Treads

  1. Apply a coat of an epoxy-based primer with a paint roller or paintbrush to the stairs.
  2. Allow the primer to dry thoroughly, generally two to four hours.
  3. Apply a coat of epoxy-based paint to the stairs and allow it to dry fully, usually two to four hours.
You might be interested:  Quick Answer: How Much Weight Can A 3/4 Inch Plywood Hold?

What should I use to finish stairs?

Best Finish For Wood Stairs

  1. Polyurethane (Surface Type Finish) Polyurethane is the best surface finish for stairs.
  2. Tung Oil (Penetrating Type Finish) Using a penetrating finish such as tung oil is a good choice for stairs when you want a more natural option.
  3. Anti-Slip Wood Stair Finishes. Bona Traffic (Anti-Slip Formula)

What should I put on my plywood stairs?

Paint the surface of the plywood stairs, both the tread and the riser, with a coat of all-in-one paint and primer. Apply paint around the four edges of each tread and riser then paint the center. Brush over the edges a second time to ensure a thick layer of paint is distributed.

Can you sand and stain plywood stairs?

You will need to seal stairs, whether painted or stained, with several coats of water-based polyurethane. Repeat for all stairs. Next, once the finish is dry, sand it with fine sandpaper (around 200 grit). When you sand, it should create dust.

What kind of wood is used for stair treads?

Oak Stair Treads Oak is a common type of wood for stair treads. It has a lot of positive qualities that make it a good option. Oak matches virtually any home style and is among the most durable of wood species. It’s also available with several additional options.

What kind of wood do you use for stair risers?

The top choices of wood for risers would be white oak, poplar. maple or pine. All of these woods have their own properties that make them suitable for making stair risers.

You might be interested:  Readers ask: What Is The Easiest Way To Cut Dadoes In Plywood?

Can I use OSB for stair treads?

Staircases aren’t always a pricey showcase in a house; as a cost-saving measure, they sometimes are constructed from OSB, which is Oriented Strand Board. OSB stair treads are sturdy and functional, but they usually require a covering to make them attractive.

How can I cover stairs?

One easier and less expensive alternative is to apply sisal or seagrass tread covers to the tread surfaces. Tread runners don’t cut down on sound as much as a continuous carpet runner might, but they are far easier to install. Tread runners also protect your stairs against wear and tear.

How do you cover MDF stairs?

Everyone here recommends the Leyland Primer Undercoat – so I was hoping to do this:

  1. Wipe down MDF stairs from dirt.
  2. Sand with P120 to get a smooth surface.
  3. Wipe off everything with TACK cloth to remove dust.
  4. A coat of Leyland Primer Undercoat (white) and then let it dry.
  5. Fine sand with P150 or P180.

How do I make my stairs smoother?

Sand the stairs with the rough sandpaper, removing any old paint and making the boards smooth and level. A mouse sander will make this job easier and enable you to get into all the corners. Make sure you do the risers as well as the treads. Then go over it with the finer sandpaper, making the surface nice and smooth.

What is the best varnish to use on stairs?

If you’re specifically looking for an anti-slip finish then Bona Traffic HD Anti Slip Varnish is probably a good option. This commercial grade varnish is very durable and hard wearing making it ideal for staircases. If an oiled finish is preferred, consider Osmo Polyx Oil Anti-Slip.

You might be interested:  Question: Which Way To Nail Plywood Sheathing?

Can you paint stairs without sanding?

To refinish wood stairs without sanding, you need to cover the stair treads with the final touch. However, before that, you need to cover all the areas you don’t want to get the paint on. Therefore, you should use painter’s tape to make sure that the paint doesn’t stray from the stair treads.

Can you sand stairs by hand?

Sand the outer portions of the stairs and the rise of each step with a small, orbital hand sander using 60-grit sandpaper. Move carefully along the edges so as not to hit the walls or handrails. Vacuum away the debris. The 120-grit sandpaper will remove the last of the old finish and leave a smooth, shiny surface.

Leave a Reply

Your email address will not be published. Required fields are marked *