- 1 Is 3/4 plywood OK for subfloor?
- 2 Is it better to nail or screw subfloor?
- 3 What size screws 3/4 plywood subfloor?
- 4 What is the best screws for subfloor?
- 5 Is it better to use OSB or plywood for subfloor?
- 6 Which side of plywood subfloor goes up?
- 7 Should you lay plywood over plank subfloor?
- 8 Should I screw down subfloor?
- 9 How do you fasten subfloor to plywood?
- 10 What size plywood should be used for a subfloor?
- 11 How do you calculate subfloor?
- 12 How do you screw down OSB subfloor?
Is 3/4 plywood OK for subfloor?
The recommended thickness of the plywood subfloor is governed by the spacing of the joists. Some experts suggest that 15/32-inch plywood should be standard if the underlying floor joists are spaced 16 inches apart or less, but slightly thicker 3 /4-inch plywood should be used for joists spaced further apart.
Is it better to nail or screw subfloor?
Using code-approved screws rather than nails is the best option for avoiding movement. If using nails for subfloor installation, stick with ring-shank nails; smooth nails may withdraw easier, leading to squeaks.
What size screws 3/4 plywood subfloor?
The 3/4-inch-thick subfloor takes a 2-inch screw. A thicker subfloor takes a 3-inch screw. Use a heavy-duty drill to drive Phillips head wood screws through the subfloor into the floor joists. Drive the screws approximately 8 inches apart.
What is the best screws for subfloor?
According to construction and renovation experts, some of the best screws for subfloor include the Senco 08200Y screws, the Simpson Strong-Tie screws, and the Hillman Group 48248 subfloor screws.
Is it better to use OSB or plywood for subfloor?
The National Tile Contractors Association and the Resilient Floor Covering Institute both recommend plywood for subflooring and underlayment, because it doesn’t have the risk of swollen edges that OSB does. Plywood also has a slight advantage in stiffness, which means that subflooring panels need not be quite as thick.
Which side of plywood subfloor goes up?
Using OSB Safely The side stamped “This Side Down” is typically the smooth side. This is mostly for roofers so that they lay the smooth side down and can stand on the rough side facing up. When installing in vertical applications such as wall sheathing, you’ll want to orient the smooth or stamped side facing out.
Should you lay plywood over plank subfloor?
Take time to make sure your existing planks are well secured in place. Repair any broken planks. Install a layer of at least ½” or preferably 5/8” ply over the existing planks. Like all wooden flooring products, it’s a good idea to acclimatise your plywood before laying it.
Should I screw down subfloor?
The fastener you choose will certainly play a part in whether your floor squeaks or not. Screws, if driven properly, prevent creaking floors. A screw firmly holds the subfloor in place, which ensures a squeak-less floor for years to come.
How do you fasten subfloor to plywood?
Attach the smaller piece to the subfloor with a 1-inch wood screw every six inches in each direction using a power drill. Push the full sheet tightly against the small section of plywood and the wall, and attach to the subfloor with a screw every six inches.
What size plywood should be used for a subfloor?
What Determines Subfloor Thickness. The minimum thickness of plywood for subflooring is about 5/8 inch. Since it does not hold fasteners as well as plywood, OSB must be a little thicker, or at least 23/32 inch.
How do you calculate subfloor?
Divide by the total square footage by the square footage of a sheet of plywood to find the number of sheets required to cover the space. A 4×8 sheet of plywood is 32 ft2. For example, if the area to be covered in plywood is 800 ft2 then 25 sheets of plywood will be needed to cover it.
How do you screw down OSB subfloor?
Use OSB panels rated for the distance between the floor joists. Run a bead of construction adhesive along each joist and lay the OSB panel on the joists. Nail the panels with 10d common nails or #10, 2 1/2-inch wood screws spaced 6 inches apart along the edges and 12 inches apart in the middle.