Quick Answer: What Size Plywood For Roof Sheathing?

What thickness should roof sheathing be?

Sheathing Thickness The typical thickness of roof sheathing is about 7/16-inch, which is just under 1/2-inch.

What grade of plywood is used for roof sheathing?

1/2 or 3/4-inch Plywood for Roof Sheathing? – Traditionally, 1/2-in CDX plywood was common choice with 24-in rafter spacing. However, heavier roof loads may require the use of 3/4-in CDX plywood for roof sheathing. Roofs with less pitch often carry heavier loads, including snow and ice accumulations in the winter.

Is OSB or plywood better for roof sheathing?

Plywood Holds the Moisture Advantage Over OSB When plywood gets wet, it tends to swell. OSB takes longer than plywood to get saturated, but also takes much longer to dry out. When used as roof sheathing, this tendency to hold moisture means it will degrade faster than plywood when exposed to chronic leaks.

Can you use 7/16 OSB on a roof?

Standard types of wood designed for roof sheathing are oriented strand board, known as OSB, and plywood, the most popular being OSB. Sheets of 7/16-inch thick, without edge support, can be used in an area where the snow load is 30 pounds per square foot.

You might be interested:  Readers ask: What Does 24 16 On Plywood Mean?

What thickness of OSB do you use for roofing?

What is the Standard Roof Sheathing Thickness? Standard roof sheathing thickness is ½” to ⅝” thick. If you are using OSB for your roof deck, then ⅝” is the recommended thickness. For plywood, which is slightly stronger than strand board, ½” thick is appropriate.

Can I use screws for roof sheathing?

Screws can be used for even greater withdrawal strength, but should be sized by the building designer. Staples are not recommended for roof sheathing attachment in high-wind areas. It is extremely important to have proper fastener spacing on all panels.

Which plywood is best for roof?

Builders love plywood for its water resistance, structural stability and low cost. They also love oriented strand board, though. It costs even less and is comparable to plywood on the other two counts, and they increasingly prefer OSB for roof sheathing. Either is an acceptable choice in most jurisdictions.

What kind of plywood is used for a roof?

CDX is the grade of plywood most commonly used for roofing (CDX plywood means it is Construction Grade for exterior purposes).

Is OSB better than plywood?

Wood fiber is used more efficiently in osb. Osb is stronger than plywood in shear. Shear values, through its thickness, are about 2 times greater than plywood. This is one of the reasons osb is used for webs of wooden I-joists.

Which is more expensive OSB or plywood?

OSB is less expensive than plywood. To build a typical 2,400-square foot home, OSB may cost $700 less than plywood. OSB is considered by many to be a “green” building material because it can be made from smaller-diameter trees, such as poplars, that are often farmed.

You might be interested:  What Is Use To Fill Plywood?

What’s better MDF or plywood?

MDF is ideal for cutting, machining and drilling, since it does not chip easily. On the other hand, plywood is a much more stronger material, which can be used for doors, floors, staircases and outdoor furniture.

Which is more water resistant OSB or plywood?

Both OSB and plywood are used for subfloors, walls and sheathing roofs. However, oriented strand board is considered to be less resistant to water (OSB swells in thickness when it is exposed to moisture), thus some people prefer using plywood for subfloors as well as roofs.

How thick should a plywood roof be?

For roof deck construction, plywood should be a minimum of 12.7 mm (1/2 in) thick. The proper thickness of the plywood panels required for a specific roof is determined by the design loads for the roof and the distance between the supporting members.

Leave a Reply

Your email address will not be published. Required fields are marked *