Readers ask: How To Make Plywood Hurricane Shutters?

What kind of plywood do you use for hurricane shutters?

Use CDX plywood at least 5/8 inch thick. Place plywood over window, allowing a 4-inch overlap on each side. Space bolts or screws 12 to 18 inches apart. Some people install homemade wood shutters by nailing plywood to the outside of window frames.

Can you make shutters out of plywood?

Step 1: If you’re making your own shutters, your best choice is 5/8-inch exterior-grade plywood. For larger windows, use 3/8-inch lag screws that are 3-1/2 inches long. You want these to penetrate the frame at least 2-1/2 inches. For installation into masonry walls, it’s a bit more difficult.

Is plywood good for hurricanes?

Boarding up doors and windows with plywood sheets is one of the most traditional ways to reinforce your home or business before a storm. With good reason, too; plywood sheets are very affordable and provide a very high level of storm and hurricane protection.

You might be interested:  Question: What Does Mdo Plywood Stand For?

Can you make hurricane shutters?

6. DIY Hurricane Shutters. To make this amazing hurricane shutter, you’ll need a sheet of CDX plywood, Philip wood screws, drill, drill bits, tape measure, concrete screws, and a few more tools. The size of the plywood will be dependent on the size of your window, so be sure to take measurements.

At what wind speed should you put up hurricane shutters?

Emergency Preparedness Director Tony Carper said most of Broward will see tropical storm force winds so homeowners should determine as best they can if their glass can withstand 60- to 70-mph winds.

Can 70 mph winds break windows?

The simple answer is yes. Hurricanes can produce extremely dangerous winds. A Category 5 storm can generate wind speeds of over 200 miles per hour. While steady wind may be unlikely to shatter a window, sudden, sharp gusts can add immense pressure to windows and doors and can break them.

How do you make outdoor louvered shutters?

Instructions

  1. Cut the Rails, Stiles, and Slats.
  2. Round Over Each Slat’s Long Edges.
  3. Cut the Mortises in the Stiles.
  4. Cut the Tenons in the Rails.
  5. Make a Louver Jig for Your Router.
  6. Cut the Grooves for the Louvers.
  7. Assemble the Louvers.
  8. Complete the Louver Assembly.

What kind of plywood do you use to cover windows?

Before hurricane season even arrives, you should purchase enough boards of 5/8-inch CDX plywood to cover all your building’s windows. CDX plywood is meant for exterior uses, so it will hold up better over time after repeated exposure to weather. Measure all your windows and pre cut the boards to fit into each one.

You might be interested:  Quick Answer: What Paint Roller Should You Use To Paint Plywood?

What do you do if you don’t have hurricane shutters?

Here are four ways to hurricane-proof your windows:

  1. Add hurricane window film. Tough, clear plastic hurricane film is popular because you can’t really see it, and you can leave it in place year-round.
  2. Shield windows with plywood.
  3. Add storm shutters.
  4. Install high-impact glass windows.
  5. Ask about home insurance discounts.

Can you board up windows from the inside?

Most folks preparing for a storm would have put the plywood on the outside of the home to protect the glass in the windows from shattering from any flying debris. And plywood on the inside could easily loosen and fall inside if the windows were shattered and gusty winds came along.

What is the best wood to make exterior shutters?

Cedar is the most common material for construction of exterior shutters because of its resistance to both insects and decay. It is a straight wood that finishes very well and can withstand harsh outdoor conditions well.

How much do accordion hurricane shutters cost?

Accordion Shutters Cost. Accordion-style hurricane shutters cost $15 to $30 per square foot plus an hourly rate of $45 to $100 to install every seven square feet.

Leave a Reply

Your email address will not be published. Required fields are marked *